4.3.3 - Analog Inputs [U3 Datasheet]

The IOTypes to retrieve a command/response analog input reading are:

LJ_ioGET_AIN       //Single-ended.  Negative channel is fixed as 31/199.
LJ_ioGET_AIN_DIFF  //Specify negative channel in x1.

The following are special channels, used with the get/put config IOTypes, to configure parameters that apply to all analog inputs:

LJ_chAIN_RESOLUTION     //QuickSample enabled if TRUE.
LJ_chAIN_SETTLING_TIME  //LongSettling enabled if TRUE.
LJ_chAIN_BINARY

Following is example pseudocode to read analog inputs:

//Execute the pin_configuration_reset IOType so that all
//pin assignments are in the factory default condition.
//The ePut function is used, which combines the add/go/get.  
ePut (lngHandle, LJ_ioPIN_CONFIGURATION_RESET, 0, 0, 0);

//Configure FIO1, FIO2, and FIO6 as analog, all others as
//digital (see Section 4.3.2).  b01000110 = 0x46 = d70.
//The ePut function is used, which combines the add/go/get.
ePut (lngHandle, LJ_ioPUT_ANALOG_ENABLE_PORT, 0, 70, 16);


//Now, an add/go/get block to execute multiple requests.

//Request a single-ended read from AIN2.
AddRequest (lngHandle, LJ_ioGET_AIN, 2, 0, 0, 0);

//Request a differential read of AIN1-AIN6.
AddRequest (lngHandle, LJ_ioGET_AIN_DIFF, 1, 0, 6, 0);

//Request a differential read of AIN1-Vref.
AddRequest (lngHandle, LJ_ioGET_AIN_DIFF, 1, 0, 30, 0);

//Request a single-ended read of AIN1.
AddRequest (lngHandle, LJ_ioGET_AIN_DIFF, 1, 0,199, 0);

//Request a read of AIN1 using the special 0-3.6 volt range.
AddRequest (lngHandle, LJ_ioGET_AIN_DIFF, 1, 0, 32, 0);

//Execute the requests.
GoOne (lngHandle);

//Since multiple requests were made with the same IOType
//and Channel, and only x1 was different, GetFirst/GetNext
//must be used to retrieve the results.  The simple
//GetResult function does not use the x1 parameter and
//thus there is no way to specify which result is desired.
//Rather than specifying the IOType and Channel of the
//result to be read, the GetFirst/GetNext functions retrieve
//the results in order.  Normally, GetFirst/GetNext are best
//used in a loop, but here they are simply called in succession.

//Retrieve AIN2 voltage.  GetFirstResult returns the IOType,
//Channel, Value, x1, and UserData from the first request.
//In this example we are just retrieving the results in order
//and Value is the only parameter we need.
GetFirstResult (lngHandle, 0, 0, &dblValue, 0, 0);

//Get the AIN1-AIN6 voltage.
GetNextResult (lngHandle, 0, 0, &dblValue, 0, 0);

//Get the AIN1-Vref voltage.
GetNextResult (lngHandle, 0, 0, &dblValue, 0, 0);

//Get the AIN1 voltage.
GetNextResult (lngHandle, 0, 0, &dblValue, 0, 0);

//Get the AIN1 voltage (special 0-3.6 volt range).
GetNextResult (lngHandle, 0, 0, &dblValue, 0, 0);